--- /dev/null
+/*
+ * $Id: header.h,v 1.1 1999/01/24 21:48:12 mj Exp $
+ *
+ * The PCI Library -- PCI Header Structure (extracted from <linux/pci.h>)
+ *
+ * Copyright (c) 1997--1999 Martin Mares <mj@atrey.karlin.mff.cuni.cz>
+ *
+ * Can be freely distributed and used under the terms of the GNU GPL.
+ */
+
+/*
+ * Under PCI, each device has 256 bytes of configuration address space,
+ * of which the first 64 bytes are standardized as follows:
+ */
+#define PCI_VENDOR_ID 0x00 /* 16 bits */
+#define PCI_DEVICE_ID 0x02 /* 16 bits */
+#define PCI_COMMAND 0x04 /* 16 bits */
+#define PCI_COMMAND_IO 0x1 /* Enable response in I/O space */
+#define PCI_COMMAND_MEMORY 0x2 /* Enable response in Memory space */
+#define PCI_COMMAND_MASTER 0x4 /* Enable bus mastering */
+#define PCI_COMMAND_SPECIAL 0x8 /* Enable response to special cycles */
+#define PCI_COMMAND_INVALIDATE 0x10 /* Use memory write and invalidate */
+#define PCI_COMMAND_VGA_PALETTE 0x20 /* Enable palette snooping */
+#define PCI_COMMAND_PARITY 0x40 /* Enable parity checking */
+#define PCI_COMMAND_WAIT 0x80 /* Enable address/data stepping */
+#define PCI_COMMAND_SERR 0x100 /* Enable SERR */
+#define PCI_COMMAND_FAST_BACK 0x200 /* Enable back-to-back writes */
+
+#define PCI_STATUS 0x06 /* 16 bits */
+#define PCI_STATUS_CAP_LIST 0x10 /* Support Capability List */
+#define PCI_STATUS_66MHZ 0x20 /* Support 66 Mhz PCI 2.1 bus */
+#define PCI_STATUS_UDF 0x40 /* Support User Definable Features */
+#define PCI_STATUS_FAST_BACK 0x80 /* Accept fast-back to back */
+#define PCI_STATUS_PARITY 0x100 /* Detected parity error */
+#define PCI_STATUS_DEVSEL_MASK 0x600 /* DEVSEL timing */
+#define PCI_STATUS_DEVSEL_FAST 0x000
+#define PCI_STATUS_DEVSEL_MEDIUM 0x200
+#define PCI_STATUS_DEVSEL_SLOW 0x400
+#define PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
+#define PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
+#define PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
+#define PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
+#define PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
+
+#define PCI_CLASS_REVISION 0x08 /* High 24 bits are class, low 8
+ revision */
+#define PCI_REVISION_ID 0x08 /* Revision ID */
+#define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */
+#define PCI_CLASS_DEVICE 0x0a /* Device class */
+
+#define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */
+#define PCI_LATENCY_TIMER 0x0d /* 8 bits */
+#define PCI_HEADER_TYPE 0x0e /* 8 bits */
+#define PCI_HEADER_TYPE_NORMAL 0
+#define PCI_HEADER_TYPE_BRIDGE 1
+#define PCI_HEADER_TYPE_CARDBUS 2
+
+#define PCI_BIST 0x0f /* 8 bits */
+#define PCI_BIST_CODE_MASK 0x0f /* Return result */
+#define PCI_BIST_START 0x40 /* 1 to start BIST, 2 secs or less */
+#define PCI_BIST_CAPABLE 0x80 /* 1 if BIST capable */
+
+/*
+ * Base addresses specify locations in memory or I/O space.
+ * Decoded size can be determined by writing a value of
+ * 0xffffffff to the register, and reading it back. Only
+ * 1 bits are decoded.
+ */
+#define PCI_BASE_ADDRESS_0 0x10 /* 32 bits */
+#define PCI_BASE_ADDRESS_1 0x14 /* 32 bits [htype 0,1 only] */
+#define PCI_BASE_ADDRESS_2 0x18 /* 32 bits [htype 0 only] */
+#define PCI_BASE_ADDRESS_3 0x1c /* 32 bits */
+#define PCI_BASE_ADDRESS_4 0x20 /* 32 bits */
+#define PCI_BASE_ADDRESS_5 0x24 /* 32 bits */
+#define PCI_BASE_ADDRESS_SPACE 0x01 /* 0 = memory, 1 = I/O */
+#define PCI_BASE_ADDRESS_SPACE_IO 0x01
+#define PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
+#define PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
+#define PCI_BASE_ADDRESS_MEM_TYPE_32 0x00 /* 32 bit address */
+#define PCI_BASE_ADDRESS_MEM_TYPE_1M 0x02 /* Below 1M */
+#define PCI_BASE_ADDRESS_MEM_TYPE_64 0x04 /* 64 bit address */
+#define PCI_BASE_ADDRESS_MEM_PREFETCH 0x08 /* prefetchable? */
+#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
+#define PCI_BASE_ADDRESS_IO_MASK (~0x03UL)
+/* bit 1 is reserved if address_space = 1 */
+
+/* Header type 0 (normal devices) */
+#define PCI_CARDBUS_CIS 0x28
+#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
+#define PCI_SUBSYSTEM_ID 0x2e
+#define PCI_ROM_ADDRESS 0x30 /* Bits 31..11 are address, 10..1 reserved */
+#define PCI_ROM_ADDRESS_ENABLE 0x01
+#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
+
+#define PCI_CAPABILITY_LIST 0x34 /* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE 0x3c /* 8 bits */
+#define PCI_INTERRUPT_PIN 0x3d /* 8 bits */
+#define PCI_MIN_GNT 0x3e /* 8 bits */
+#define PCI_MAX_LAT 0x3f /* 8 bits */
+
+/* Header type 1 (PCI-to-PCI bridges) */
+#define PCI_PRIMARY_BUS 0x18 /* Primary bus number */
+#define PCI_SECONDARY_BUS 0x19 /* Secondary bus number */
+#define PCI_SUBORDINATE_BUS 0x1a /* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER 0x1b /* Latency timer for secondary interface */
+#define PCI_IO_BASE 0x1c /* I/O range behind the bridge */
+#define PCI_IO_LIMIT 0x1d
+#define PCI_IO_RANGE_TYPE_MASK 0x0f /* I/O bridging type */
+#define PCI_IO_RANGE_TYPE_16 0x00
+#define PCI_IO_RANGE_TYPE_32 0x01
+#define PCI_IO_RANGE_MASK ~0x0f
+#define PCI_SEC_STATUS 0x1e /* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE 0x20 /* Memory range behind */
+#define PCI_MEMORY_LIMIT 0x22
+#define PCI_MEMORY_RANGE_TYPE_MASK 0x0f
+#define PCI_MEMORY_RANGE_MASK ~0x0f
+#define PCI_PREF_MEMORY_BASE 0x24 /* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT 0x26
+#define PCI_PREF_RANGE_TYPE_MASK 0x0f
+#define PCI_PREF_RANGE_TYPE_32 0x00
+#define PCI_PREF_RANGE_TYPE_64 0x01
+#define PCI_PREF_RANGE_MASK ~0x0f
+#define PCI_PREF_BASE_UPPER32 0x28 /* Upper half of prefetchable memory range */
+#define PCI_PREF_LIMIT_UPPER32 0x2c
+#define PCI_IO_BASE_UPPER16 0x30 /* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16 0x32
+/* 0x34-0x3b is reserved */
+#define PCI_ROM_ADDRESS1 0x38 /* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL 0x3e
+#define PCI_BRIDGE_CTL_PARITY 0x01 /* Enable parity detection on secondary interface */
+#define PCI_BRIDGE_CTL_SERR 0x02 /* The same for SERR forwarding */
+#define PCI_BRIDGE_CTL_NO_ISA 0x04 /* Disable bridging of ISA ports */
+#define PCI_BRIDGE_CTL_VGA 0x08 /* Forward VGA addresses */
+#define PCI_BRIDGE_CTL_MASTER_ABORT 0x20 /* Report master aborts */
+#define PCI_BRIDGE_CTL_BUS_RESET 0x40 /* Secondary bus reset */
+#define PCI_BRIDGE_CTL_FAST_BACK 0x80 /* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+/* 0x14-0x15 reserved */
+#define PCI_CB_SEC_STATUS 0x16 /* Secondary status */
+#define PCI_CB_PRIMARY_BUS 0x18 /* PCI bus number */
+#define PCI_CB_CARD_BUS 0x19 /* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS 0x1a /* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER 0x1b /* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0 0x1c
+#define PCI_CB_MEMORY_LIMIT_0 0x20
+#define PCI_CB_MEMORY_BASE_1 0x24
+#define PCI_CB_MEMORY_LIMIT_1 0x28
+#define PCI_CB_IO_BASE_0 0x2c
+#define PCI_CB_IO_BASE_0_HI 0x2e
+#define PCI_CB_IO_LIMIT_0 0x30
+#define PCI_CB_IO_LIMIT_0_HI 0x32
+#define PCI_CB_IO_BASE_1 0x34
+#define PCI_CB_IO_BASE_1_HI 0x36
+#define PCI_CB_IO_LIMIT_1 0x38
+#define PCI_CB_IO_LIMIT_1_HI 0x3a
+#define PCI_CB_IO_RANGE_MASK ~0x03
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL 0x3e
+#define PCI_CB_BRIDGE_CTL_PARITY 0x01 /* Similar to standard bridge control register */
+#define PCI_CB_BRIDGE_CTL_SERR 0x02
+#define PCI_CB_BRIDGE_CTL_ISA 0x04
+#define PCI_CB_BRIDGE_CTL_VGA 0x08
+#define PCI_CB_BRIDGE_CTL_MASTER_ABORT 0x20
+#define PCI_CB_BRIDGE_CTL_CB_RESET 0x40 /* CardBus reset */
+#define PCI_CB_BRIDGE_CTL_16BIT_INT 0x80 /* Enable interrupt for 16-bit cards */
+#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100 /* Prefetch enable for both memory regions */
+#define PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define PCI_CB_BRIDGE_CTL_POST_WRITES 0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
+#define PCI_CB_SUBSYSTEM_ID 0x42
+#define PCI_CB_LEGACY_MODE_BASE 0x44 /* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+#define PCI_CAP_LIST_ID 0 /* Capability ID */
+#define PCI_CAP_ID_AGP 0x02
+#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
+#define PCI_CAP_LIST_REVISION 2 /* Revision of this capability (BCD) */
+/* 3 reserved */
+
+/*
+ * The PCI interface treats multi-function devices as independent
+ * devices. The slot/function address of each device is encoded
+ * in a single byte as follows:
+ *
+ * 7:3 = slot
+ * 2:0 = function
+ */
+#define PCI_DEVFN(slot,func) ((((slot) & 0x1f) << 3) | ((func) & 0x07))
+#define PCI_SLOT(devfn) (((devfn) >> 3) & 0x1f)
+#define PCI_FUNC(devfn) ((devfn) & 0x07)
+
+/* Device classes and subclasses */
+
+#define PCI_CLASS_NOT_DEFINED 0x0000
+#define PCI_CLASS_NOT_DEFINED_VGA 0x0001
+
+#define PCI_BASE_CLASS_STORAGE 0x01
+#define PCI_CLASS_STORAGE_SCSI 0x0100
+#define PCI_CLASS_STORAGE_IDE 0x0101
+#define PCI_CLASS_STORAGE_FLOPPY 0x0102
+#define PCI_CLASS_STORAGE_IPI 0x0103
+#define PCI_CLASS_STORAGE_RAID 0x0104
+#define PCI_CLASS_STORAGE_OTHER 0x0180
+
+#define PCI_BASE_CLASS_NETWORK 0x02
+#define PCI_CLASS_NETWORK_ETHERNET 0x0200
+#define PCI_CLASS_NETWORK_TOKEN_RING 0x0201
+#define PCI_CLASS_NETWORK_FDDI 0x0202
+#define PCI_CLASS_NETWORK_ATM 0x0203
+#define PCI_CLASS_NETWORK_OTHER 0x0280
+
+#define PCI_BASE_CLASS_DISPLAY 0x03
+#define PCI_CLASS_DISPLAY_VGA 0x0300
+#define PCI_CLASS_DISPLAY_XGA 0x0301
+#define PCI_CLASS_DISPLAY_OTHER 0x0380
+
+#define PCI_BASE_CLASS_MULTIMEDIA 0x04
+#define PCI_CLASS_MULTIMEDIA_VIDEO 0x0400
+#define PCI_CLASS_MULTIMEDIA_AUDIO 0x0401
+#define PCI_CLASS_MULTIMEDIA_OTHER 0x0480
+
+#define PCI_BASE_CLASS_MEMORY 0x05
+#define PCI_CLASS_MEMORY_RAM 0x0500
+#define PCI_CLASS_MEMORY_FLASH 0x0501
+#define PCI_CLASS_MEMORY_OTHER 0x0580
+
+#define PCI_BASE_CLASS_BRIDGE 0x06
+#define PCI_CLASS_BRIDGE_HOST 0x0600
+#define PCI_CLASS_BRIDGE_ISA 0x0601
+#define PCI_CLASS_BRIDGE_EISA 0x0602
+#define PCI_CLASS_BRIDGE_MC 0x0603
+#define PCI_CLASS_BRIDGE_PCI 0x0604
+#define PCI_CLASS_BRIDGE_PCMCIA 0x0605
+#define PCI_CLASS_BRIDGE_NUBUS 0x0606
+#define PCI_CLASS_BRIDGE_CARDBUS 0x0607
+#define PCI_CLASS_BRIDGE_OTHER 0x0680
+
+#define PCI_BASE_CLASS_COMMUNICATION 0x07
+#define PCI_CLASS_COMMUNICATION_SERIAL 0x0700
+#define PCI_CLASS_COMMUNICATION_PARALLEL 0x0701
+#define PCI_CLASS_COMMUNICATION_OTHER 0x0780
+
+#define PCI_BASE_CLASS_SYSTEM 0x08
+#define PCI_CLASS_SYSTEM_PIC 0x0800
+#define PCI_CLASS_SYSTEM_DMA 0x0801
+#define PCI_CLASS_SYSTEM_TIMER 0x0802
+#define PCI_CLASS_SYSTEM_RTC 0x0803
+#define PCI_CLASS_SYSTEM_OTHER 0x0880
+
+#define PCI_BASE_CLASS_INPUT 0x09
+#define PCI_CLASS_INPUT_KEYBOARD 0x0900
+#define PCI_CLASS_INPUT_PEN 0x0901
+#define PCI_CLASS_INPUT_MOUSE 0x0902
+#define PCI_CLASS_INPUT_OTHER 0x0980
+
+#define PCI_BASE_CLASS_DOCKING 0x0a
+#define PCI_CLASS_DOCKING_GENERIC 0x0a00
+#define PCI_CLASS_DOCKING_OTHER 0x0a01
+
+#define PCI_BASE_CLASS_PROCESSOR 0x0b
+#define PCI_CLASS_PROCESSOR_386 0x0b00
+#define PCI_CLASS_PROCESSOR_486 0x0b01
+#define PCI_CLASS_PROCESSOR_PENTIUM 0x0b02
+#define PCI_CLASS_PROCESSOR_ALPHA 0x0b10
+#define PCI_CLASS_PROCESSOR_POWERPC 0x0b20
+#define PCI_CLASS_PROCESSOR_CO 0x0b40
+
+#define PCI_BASE_CLASS_SERIAL 0x0c
+#define PCI_CLASS_SERIAL_FIREWIRE 0x0c00
+#define PCI_CLASS_SERIAL_ACCESS 0x0c01
+#define PCI_CLASS_SERIAL_SSA 0x0c02
+#define PCI_CLASS_SERIAL_USB 0x0c03
+#define PCI_CLASS_SERIAL_FIBER 0x0c04
+
+#define PCI_CLASS_OTHERS 0xff
+
+/* Several ID's we need in the library */
+
+#define PCI_VENDOR_ID_INTEL 0x8086
+#define PCI_VENDOR_ID_COMPAQ 0x0e11
projects / pciutils.git / commitdiff