/*
- * $Id: header.h,v 1.4 1999/07/07 11:23:10 mj Exp $
+ * $Id: header.h,v 1.9 2002/12/26 20:24:50 mj Exp $
*
* The PCI Library -- PCI Header Structure (extracted from <linux/pci.h>)
*
- * Copyright (c) 1997--1999 Martin Mares <mj@atrey.karlin.mff.cuni.cz>
+ * Copyright (c) 1997--2002 Martin Mares <mj@ucw.cz>
*
* Can be freely distributed and used under the terms of the GNU GPL.
*/
#define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */
#define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */
#define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */
+#define PCI_CAP_ID_PCIX 0x07 /* PCI-X */
#define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */
#define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */
#define PCI_CAP_SIZEOF 4
/* Power Management Registers */
-#define PCI_PM_CAP_VER_MASK 0x0007 /* Version */
-#define PCI_PM_CAP_PME_CLOCK 0x0008 /* PME clock required */
-#define PCI_PM_CAP_AUX_POWER 0x0010 /* Auxilliary power support */
-#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization */
+#define PCI_PM_CAP_VER_MASK 0x0007 /* Version (2=PM1.1) */
+#define PCI_PM_CAP_PME_CLOCK 0x0008 /* Clock required for PME generation */
+#define PCI_PM_CAP_DSI 0x0020 /* Device specific initialization required */
+#define PCI_PM_CAP_AUX_C_MASK 0x01c0 /* Maximum aux current required in D3cold */
#define PCI_PM_CAP_D1 0x0200 /* D1 power state support */
#define PCI_PM_CAP_D2 0x0400 /* D2 power state support */
-#define PCI_PM_CAP_PME 0x0800 /* PME pin supported */
+#define PCI_PM_CAP_PME_D0 0x0800 /* PME can be asserted from D0 */
+#define PCI_PM_CAP_PME_D1 0x1000 /* PME can be asserted from D1 */
+#define PCI_PM_CAP_PME_D2 0x2000 /* PME can be asserted from D2 */
+#define PCI_PM_CAP_PME_D3_HOT 0x4000 /* PME can be asserted from D3hot */
+#define PCI_PM_CAP_PME_D3_COLD 0x8000 /* PME can be asserted from D3cold */
#define PCI_PM_CTRL 4 /* PM control and status register */
#define PCI_PM_CTRL_STATE_MASK 0x0003 /* Current power state (D0 to D3) */
#define PCI_PM_CTRL_PME_ENABLE 0x0100 /* PME pin enable */
-#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* Data select (??) */
-#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* Data scale (??) */
+#define PCI_PM_CTRL_DATA_SEL_MASK 0x1e00 /* PM table data index */
+#define PCI_PM_CTRL_DATA_SCALE_MASK 0x6000 /* PM table data scaling factor */
#define PCI_PM_CTRL_PME_STATUS 0x8000 /* PME pin status */
-#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions (??) */
-#define PCI_PM_PPB_B2_B3 0x40 /* Stop clock when in D3hot (??) */
-#define PCI_PM_BPCC_ENABLE 0x80 /* Bus power/clock control enable (??) */
-#define PCI_PM_DATA_REGISTER 7 /* (??) */
+#define PCI_PM_PPB_EXTENSIONS 6 /* PPB support extensions */
+#define PCI_PM_PPB_B2_B3 0x40 /* If bridge enters D3hot, bus enters: 0=B3, 1=B2 */
+#define PCI_PM_BPCC_ENABLE 0x80 /* Secondary bus is power managed */
+#define PCI_PM_DATA_REGISTER 7 /* PM table contents read here */
#define PCI_PM_SIZEOF 8
/* AGP registers */
#define PCI_AGP_RFU 3 /* Rest of capability flags */
#define PCI_AGP_STATUS 4 /* Status register */
#define PCI_AGP_STATUS_RQ_MASK 0xff000000 /* Maximum number of requests - 1 */
+#define PCI_AGP_STATUS_ISOCH 0x10000 /* Isochronous transactions supported */
+#define PCI_AGP_STATUS_ARQSZ_MASK 0xe000 /* log2(optimum async req size in bytes) - 4 */
+#define PCI_AGP_STATUS_CAL_MASK 0x1c00 /* Calibration cycle timing */
#define PCI_AGP_STATUS_SBA 0x0200 /* Sideband addressing supported */
-#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing supported */
-#define PCI_AGP_STATUS_FW 0x0010 /* FW transfers supported */
-#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported */
-#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported */
-#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported */
+#define PCI_AGP_STATUS_ITA_COH 0x0100 /* In-aperture accesses always coherent */
+#define PCI_AGP_STATUS_GART64 0x0080 /* 64-bit GART entries supported */
+#define PCI_AGP_STATUS_HTRANS 0x0040 /* If 0, core logic can xlate host CPU accesses thru aperture */
+#define PCI_AGP_STATUS_64BIT 0x0020 /* 64-bit addressing cycles supported */
+#define PCI_AGP_STATUS_FW 0x0010 /* Fast write transfers supported */
+#define PCI_AGP_STATUS_AGP3 0x0008 /* AGP3 mode supported */
+#define PCI_AGP_STATUS_RATE4 0x0004 /* 4x transfer rate supported (RFU in AGP3 mode) */
+#define PCI_AGP_STATUS_RATE2 0x0002 /* 2x transfer rate supported (8x in AGP3 mode) */
+#define PCI_AGP_STATUS_RATE1 0x0001 /* 1x transfer rate supported (4x in AGP3 mode) */
#define PCI_AGP_COMMAND 8 /* Control register */
#define PCI_AGP_COMMAND_RQ_MASK 0xff000000 /* Master: Maximum number of requests */
+#define PCI_AGP_COMMAND_ARQSZ_MASK 0xe000 /* log2(optimum async req size in bytes) - 4 */
+#define PCI_AGP_COMMAND_CAL_MASK 0x1c00 /* Calibration cycle timing */
#define PCI_AGP_COMMAND_SBA 0x0200 /* Sideband addressing enabled */
#define PCI_AGP_COMMAND_AGP 0x0100 /* Allow processing of AGP transactions */
-#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow processing of 64-bit addresses */
-#define PCI_AGP_COMMAND_FW 0x0010 /* Force FW transfers */
-#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate */
-#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 4x rate */
-#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 4x rate */
+#define PCI_AGP_COMMAND_GART64 0x0080 /* 64-bit GART entries enabled */
+#define PCI_AGP_COMMAND_64BIT 0x0020 /* Allow generation of 64-bit addr cycles */
+#define PCI_AGP_COMMAND_FW 0x0010 /* Enable FW transfers */
+#define PCI_AGP_COMMAND_RATE4 0x0004 /* Use 4x rate (RFU in AGP3 mode) */
+#define PCI_AGP_COMMAND_RATE2 0x0002 /* Use 2x rate (8x in AGP3 mode) */
+#define PCI_AGP_COMMAND_RATE1 0x0001 /* Use 1x rate (4x in AGP3 mode) */
#define PCI_AGP_SIZEOF 12
/* Slot Identification */
#define PCI_MSI_DATA_32 8 /* 16 bits of data for 32-bit devices */
#define PCI_MSI_DATA_64 12 /* 16 bits of data for 64-bit devices */
+/* PCI-X */
+#define PCI_PCIX_COMMAND 2 /* Command register offset */
+#define PCI_PCIX_COMMAND_DPERE 0x0001 /* Data Parity Error Recover Enable */
+#define PCI_PCIX_COMMAND_ERO 0x0002 /* Enable Relaxed Ordering */
+#define PCI_PCIX_COMMAND_MAX_MEM_READ_BYTE_COUNT 0x000c /* Maximum Memory Read Byte Count */
+#define PCI_PCIX_COMMAND_MAX_OUTSTANDING_SPLIT_TRANS 0x0070
+#define PCI_PCIX_COMMAND_RESERVED 0xf80
+#define PCI_PCIX_STATUS 4 /* Status register offset */
+#define PCI_PCIX_STATUS_FUNCTION 0x00000007
+#define PCI_PCIX_STATUS_DEVICE 0x000000f8
+#define PCI_PCIX_STATUS_BUS 0x0000ff00
+#define PCI_PCIX_STATUS_64BIT 0x00010000
+#define PCI_PCIX_STATUS_133MHZ 0x00020000
+#define PCI_PCIX_STATUS_SC_DISCARDED 0x00040000 /* Split Completion Discarded */
+#define PCI_PCIX_STATUS_UNEXPECTED_SC 0x00080000 /* Unexpected Split Completion */
+#define PCI_PCIX_STATUS_DEVICE_COMPLEXITY 0x00100000 /* 0 = simple device, 1 = bridge device */
+#define PCI_PCIX_STATUS_DESIGNED_MAX_MEM_READ_BYTE_COUNT 0x00600000 /* 0 = 512 bytes, 1 = 1024, 2 = 2048, 3 = 4096 */
+#define PCI_PCIX_STATUS_DESIGNED_MAX_OUTSTANDING_SPLIT_TRANS 0x03800000
+#define PCI_PCIX_STATUS_DESIGNED_MAX_CUMULATIVE_READ_SIZE 0x1c000000
+#define PCI_PCIX_STATUS_RCVD_SC_ERR_MESS 0x20000000 /* Received Split Completion Error Message */
+#define PCI_PCIX_STATUS_RESERVED 0xc0000000
+#define PCI_PCIX_SIZEOF 4
+
+/* PCI-X Bridges */
+#define PCI_PCIX_BRIDGE_SEC_STATUS 2 /* Secondary bus status register offset */
+#define PCI_PCIX_BRIDGE_SEC_STATUS_64BIT 0x0001
+#define PCI_PCIX_BRIDGE_SEC_STATUS_133MHZ 0x0002
+#define PCI_PCIX_BRIDGE_SEC_STATUS_SC_DISCARDED 0x0004 /* Split Completion Discarded on secondary bus */
+#define PCI_PCIX_BRIDGE_SEC_STATUS_UNEXPECTED_SC 0x0008 /* Unexpected Split Completion on secondary bus */
+#define PCI_PCIX_BRIDGE_SEC_STATUS_SC_OVERRUN 0x0010 /* Split Completion Overrun on secondary bus */
+#define PCI_PCIX_BRIDGE_SEC_STATUS_SPLIT_REQUEST_DELAYED 0x0020
+#define PCI_PCIX_BRIDGE_SEC_STATUS_CLOCK_FREQ 0x01c0
+#define PCI_PCIX_BRIDGE_SEC_STATUS_RESERVED 0xfe00
+#define PCI_PCIX_BRIDGE_STATUS 4 /* Primary bus status register offset */
+#define PCI_PCIX_BRIDGE_STATUS_FUNCTION 0x00000007
+#define PCI_PCIX_BRIDGE_STATUS_DEVICE 0x000000f8
+#define PCI_PCIX_BRIDGE_STATUS_BUS 0x0000ff00
+#define PCI_PCIX_BRIDGE_STATUS_64BIT 0x00010000
+#define PCI_PCIX_BRIDGE_STATUS_133MHZ 0x00020000
+#define PCI_PCIX_BRIDGE_STATUS_SC_DISCARDED 0x00040000 /* Split Completion Discarded */
+#define PCI_PCIX_BRIDGE_STATUS_UNEXPECTED_SC 0x00080000 /* Unexpected Split Completion */
+#define PCI_PCIX_BRIDGE_STATUS_SC_OVERRUN 0x00100000 /* Split Completion Overrun */
+#define PCI_PCIX_BRIDGE_STATUS_SPLIT_REQUEST_DELAYED 0x00200000
+#define PCI_PCIX_BRIDGE_STATUS_RESERVED 0xffc00000
+#define PCI_PCIX_BRIDGE_UPSTREAM_SPLIT_TRANS_CTRL 8 /* Upstream Split Transaction Register offset */
+#define PCI_PCIX_BRIDGE_DOWNSTREAM_SPLIT_TRANS_CTRL 12 /* Downstream Split Transaction Register offset */
+#define PCI_PCIX_BRIDGE_STR_CAPACITY 0x0000ffff
+#define PCI_PCIX_BRIDGE_STR_COMMITMENT_LIMIT 0xffff0000
+#define PCI_PCIX_BRIDGE_SIZEOF 12
+
/*
* The PCI interface treats multi-function devices as independent
* devices. The slot/function address of each device is encoded
projects / pciutils.git / blobdiff