2 ******************************************************************************
3 * @file stm32f0xx_hal_conf.h
4 * @brief HAL configuration file.
5 ******************************************************************************
8 * <h2><center>© COPYRIGHT(c) 2018 STMicroelectronics</center></h2>
10 * Redistribution and use in source and binary forms, with or without modification,
11 * are permitted provided that the following conditions are met:
12 * 1. Redistributions of source code must retain the above copyright notice,
13 * this list of conditions and the following disclaimer.
14 * 2. Redistributions in binary form must reproduce the above copyright notice,
15 * this list of conditions and the following disclaimer in the documentation
16 * and/or other materials provided with the distribution.
17 * 3. Neither the name of STMicroelectronics nor the names of its contributors
18 * may be used to endorse or promote products derived from this software
19 * without specific prior written permission.
21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
32 ******************************************************************************
35 /* Define to prevent recursive inclusion -------------------------------------*/
36 #ifndef __STM32F0xx_HAL_CONF_H
37 #define __STM32F0xx_HAL_CONF_H
44 /* Exported types ------------------------------------------------------------*/
45 /* Exported constants --------------------------------------------------------*/
47 /* ########################## Module Selection ############################## */
49 * @brief This is the list of modules to be used in the HAL driver
51 #define HAL_MODULE_ENABLED
52 /*#define HAL_ADC_MODULE_ENABLED */
53 /*#define HAL_CRYP_MODULE_ENABLED */
54 /*#define HAL_CAN_MODULE_ENABLED */
55 /*#define HAL_CEC_MODULE_ENABLED */
56 /*#define HAL_COMP_MODULE_ENABLED */
57 /*#define HAL_CRC_MODULE_ENABLED */
58 /*#define HAL_CRYP_MODULE_ENABLED */
59 /*#define HAL_TSC_MODULE_ENABLED */
60 /*#define HAL_DAC_MODULE_ENABLED */
61 /*#define HAL_I2S_MODULE_ENABLED */
62 /*#define HAL_IWDG_MODULE_ENABLED */
63 /*#define HAL_LCD_MODULE_ENABLED */
64 /*#define HAL_LPTIM_MODULE_ENABLED */
65 /*#define HAL_RNG_MODULE_ENABLED */
66 /*#define HAL_RTC_MODULE_ENABLED */
67 /*#define HAL_SPI_MODULE_ENABLED */
68 /*#define HAL_TIM_MODULE_ENABLED */
69 /*#define HAL_UART_MODULE_ENABLED */
70 /*#define HAL_USART_MODULE_ENABLED */
71 /*#define HAL_IRDA_MODULE_ENABLED */
72 /*#define HAL_SMARTCARD_MODULE_ENABLED */
73 /*#define HAL_SMBUS_MODULE_ENABLED */
74 /*#define HAL_WWDG_MODULE_ENABLED */
75 /*#define HAL_PCD_MODULE_ENABLED */
76 #define HAL_CORTEX_MODULE_ENABLED
77 #define HAL_DMA_MODULE_ENABLED
78 #define HAL_FLASH_MODULE_ENABLED
79 #define HAL_GPIO_MODULE_ENABLED
80 #define HAL_PWR_MODULE_ENABLED
81 #define HAL_RCC_MODULE_ENABLED
82 #define HAL_I2C_MODULE_ENABLED
84 /* ########################## HSE/HSI Values adaptation ##################### */
86 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
87 * This value is used by the RCC HAL module to compute the system frequency
88 * (when HSE is used as system clock source, directly or through the PLL).
90 #if !defined (HSE_VALUE)
91 #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
92 #endif /* HSE_VALUE */
95 * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
98 #if !defined (HSE_STARTUP_TIMEOUT)
99 #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
100 #endif /* HSE_STARTUP_TIMEOUT */
103 * @brief Internal High Speed oscillator (HSI) value.
104 * This value is used by the RCC HAL module to compute the system frequency
105 * (when HSI is used as system clock source, directly or through the PLL).
107 #if !defined (HSI_VALUE)
108 #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
109 #endif /* HSI_VALUE */
112 * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
115 #if !defined (HSI_STARTUP_TIMEOUT)
116 #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */
117 #endif /* HSI_STARTUP_TIMEOUT */
120 * @brief Internal High Speed oscillator for ADC (HSI14) value.
122 #if !defined (HSI14_VALUE)
123 #define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz.
124 The real value may vary depending on the variations
125 in voltage and temperature. */
126 #endif /* HSI14_VALUE */
129 * @brief Internal High Speed oscillator for USB (HSI48) value.
131 #if !defined (HSI48_VALUE)
132 #define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz.
133 The real value may vary depending on the variations
134 in voltage and temperature. */
135 #endif /* HSI48_VALUE */
138 * @brief Internal Low Speed oscillator (LSI) value.
140 #if !defined (LSI_VALUE)
141 #define LSI_VALUE ((uint32_t)40000)
142 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
143 The real value may vary depending on the variations
144 in voltage and temperature. */
146 * @brief External Low Speed oscillator (LSI) value.
148 #if !defined (LSE_VALUE)
149 #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
150 #endif /* LSE_VALUE */
152 #if !defined (LSE_STARTUP_TIMEOUT)
153 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
154 #endif /* LSE_STARTUP_TIMEOUT */
156 /* Tip: To avoid modifying this file each time you need to use different HSE,
157 === you can define the HSE value in your toolchain compiler preprocessor. */
159 /* ########################### System Configuration ######################### */
161 * @brief This is the HAL system configuration section
163 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
164 #define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */
165 /* Warning: Must be set to higher priority for HAL_Delay() */
166 /* and HAL_GetTick() usage under interrupt context */
168 #define PREFETCH_ENABLE 1
169 #define INSTRUCTION_CACHE_ENABLE 0
170 #define DATA_CACHE_ENABLE 0
171 /* ########################## Assert Selection ############################## */
173 * @brief Uncomment the line below to expanse the "assert_param" macro in the
176 /* #define USE_FULL_ASSERT 1U */
178 /* ################## SPI peripheral configuration ########################## */
180 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
181 * Activated: CRC code is present inside driver
182 * Deactivated: CRC code cleaned from driver
185 #define USE_SPI_CRC 0U
187 /* Includes ------------------------------------------------------------------*/
189 * @brief Include module's header file
192 #ifdef HAL_RCC_MODULE_ENABLED
193 #include "stm32f0xx_hal_rcc.h"
194 #endif /* HAL_RCC_MODULE_ENABLED */
196 #ifdef HAL_GPIO_MODULE_ENABLED
197 #include "stm32f0xx_hal_gpio.h"
198 #endif /* HAL_GPIO_MODULE_ENABLED */
200 #ifdef HAL_DMA_MODULE_ENABLED
201 #include "stm32f0xx_hal_dma.h"
202 #endif /* HAL_DMA_MODULE_ENABLED */
204 #ifdef HAL_CORTEX_MODULE_ENABLED
205 #include "stm32f0xx_hal_cortex.h"
206 #endif /* HAL_CORTEX_MODULE_ENABLED */
208 #ifdef HAL_ADC_MODULE_ENABLED
209 #include "stm32f0xx_hal_adc.h"
210 #endif /* HAL_ADC_MODULE_ENABLED */
212 #ifdef HAL_CAN_MODULE_ENABLED
213 #include "stm32f0xx_hal_can.h"
214 #endif /* HAL_CAN_MODULE_ENABLED */
216 #ifdef HAL_CEC_MODULE_ENABLED
217 #include "stm32f0xx_hal_cec.h"
218 #endif /* HAL_CEC_MODULE_ENABLED */
220 #ifdef HAL_COMP_MODULE_ENABLED
221 #include "stm32f0xx_hal_comp.h"
222 #endif /* HAL_COMP_MODULE_ENABLED */
224 #ifdef HAL_CRC_MODULE_ENABLED
225 #include "stm32f0xx_hal_crc.h"
226 #endif /* HAL_CRC_MODULE_ENABLED */
228 #ifdef HAL_DAC_MODULE_ENABLED
229 #include "stm32f0xx_hal_dac.h"
230 #endif /* HAL_DAC_MODULE_ENABLED */
232 #ifdef HAL_FLASH_MODULE_ENABLED
233 #include "stm32f0xx_hal_flash.h"
234 #endif /* HAL_FLASH_MODULE_ENABLED */
236 #ifdef HAL_I2C_MODULE_ENABLED
237 #include "stm32f0xx_hal_i2c.h"
238 #endif /* HAL_I2C_MODULE_ENABLED */
240 #ifdef HAL_I2S_MODULE_ENABLED
241 #include "stm32f0xx_hal_i2s.h"
242 #endif /* HAL_I2S_MODULE_ENABLED */
244 #ifdef HAL_IRDA_MODULE_ENABLED
245 #include "stm32f0xx_hal_irda.h"
246 #endif /* HAL_IRDA_MODULE_ENABLED */
248 #ifdef HAL_IWDG_MODULE_ENABLED
249 #include "stm32f0xx_hal_iwdg.h"
250 #endif /* HAL_IWDG_MODULE_ENABLED */
252 #ifdef HAL_PCD_MODULE_ENABLED
253 #include "stm32f0xx_hal_pcd.h"
254 #endif /* HAL_PCD_MODULE_ENABLED */
256 #ifdef HAL_PWR_MODULE_ENABLED
257 #include "stm32f0xx_hal_pwr.h"
258 #endif /* HAL_PWR_MODULE_ENABLED */
260 #ifdef HAL_RTC_MODULE_ENABLED
261 #include "stm32f0xx_hal_rtc.h"
262 #endif /* HAL_RTC_MODULE_ENABLED */
264 #ifdef HAL_SMARTCARD_MODULE_ENABLED
265 #include "stm32f0xx_hal_smartcard.h"
266 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
268 #ifdef HAL_SMBUS_MODULE_ENABLED
269 #include "stm32f0xx_hal_smbus.h"
270 #endif /* HAL_SMBUS_MODULE_ENABLED */
272 #ifdef HAL_SPI_MODULE_ENABLED
273 #include "stm32f0xx_hal_spi.h"
274 #endif /* HAL_SPI_MODULE_ENABLED */
276 #ifdef HAL_TIM_MODULE_ENABLED
277 #include "stm32f0xx_hal_tim.h"
278 #endif /* HAL_TIM_MODULE_ENABLED */
280 #ifdef HAL_TSC_MODULE_ENABLED
281 #include "stm32f0xx_hal_tsc.h"
282 #endif /* HAL_TSC_MODULE_ENABLED */
284 #ifdef HAL_UART_MODULE_ENABLED
285 #include "stm32f0xx_hal_uart.h"
286 #endif /* HAL_UART_MODULE_ENABLED */
288 #ifdef HAL_USART_MODULE_ENABLED
289 #include "stm32f0xx_hal_usart.h"
290 #endif /* HAL_USART_MODULE_ENABLED */
292 #ifdef HAL_WWDG_MODULE_ENABLED
293 #include "stm32f0xx_hal_wwdg.h"
294 #endif /* HAL_WWDG_MODULE_ENABLED */
296 /* Exported macro ------------------------------------------------------------*/
297 #ifdef USE_FULL_ASSERT
299 * @brief The assert_param macro is used for function's parameters check.
300 * @param expr: If expr is false, it calls assert_failed function
301 * which reports the name of the source file and the source
302 * line number of the call that failed.
303 * If expr is true, it returns no value.
306 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
307 /* Exported functions ------------------------------------------------------- */
308 void assert_failed(uint8_t* file, uint32_t line);
310 #define assert_param(expr) ((void)0U)
311 #endif /* USE_FULL_ASSERT */
317 #endif /* __STM32F0xx_HAL_CONF_H */
319 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/