[pciutils.git] / ChangeLog

2007-10-19  Martin Mares <mj@ucw.cz>

        * pci.ids: Revised class codes to match Conventional PCI 3.0 specs.
        Added a couple of new ones, renumbered `ADMA continuous operation'
        prog-if to 0x30 (even the old SATA Class Code ECN doesn't mention
        0x40) and renumbered the satellite communication controllers.

2007-10-14  Martin Mares <mj@ucw.cz>

        * lib/[fno]bsd-*: Removed extraneous braces.

2007-10-12  Martin Mares <mj@ucw.cz>

        * Capability loop detection introduced 2.2.7 did not work
          properly with extended capabilities. Fixed.

2007-10-05  Martin Mares <mj@ucw.cz>

        * Released as 2.2.7.

        * lspci.c (show_caps, show_ext_caps): Detect and report loops in
        capability lists.

        * lspci.c, lib/header.h: Finished decoding of the PCI Express
        capability. The extended capabilities remain undecoded for now,
        but at least the list of them has been updated to reflect the
        current PCI Express 2.0 spec.

        * lspci.c, lib/header.h: Decode new bits of traditional registers
        as defined by PCIE / PCI-X. This includes discard timers in the bridge
        control register and INTx enable/status in device control/status
        registers.

        * lib/fbsd-device.c: Support domains on new FreeBSD's. Contributed
        by Marius Strobl.

2007-09-12  Hasso Tepper <hasso@estpak.ee>

        * Extended the fbsd-device backend to run on Dragonfly BSD.

        * lspci.c: alloca() is declared in <stdlib.h> on BSD's, not <alloca.h>.

2007-09-03  Martin Mares <mj@ucw.cz>

        * Resurrected the Windows port, including cross-compilation by MinGW.
        Patch by Samuel Bronson <naesten@gmail.com>.

2007-08-31  Martin Mares <mj@ucw.cz>

        * Makefile, lib/Makefile: `ar' and `ranlib' can be overriden to allow
        cross-compilation.

2007-08-27  Martin Mares  <mj@ucw.cz>

        * lib/names.c (pci_open): When calling gzopen(), use "rb" file mode
        instead of "r". This is needed on DOS systems, where this function
        somewhat illogically uses the binary flag for the compressed file
        instead of the decompressed stream inside, where binariness really
        matters.

2007-08-14  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_ht): Added decoding of Hypertransport MSI mapping capability,
        based on a patch by Jason Gunthorpe.

        * tests/cap-MSI-mapping: Added a test case. I plan to add test cases
        (which are dumps of config space) for all new features.

2007-06-20  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.6.

        * Makefile: Added an "install-lib" target. Thanks to Dan Nicholson
        for a patch.

        * Makefile, lib/Makefile: Generate and install pkg-config file
        for libpci. Again by Dan Nicholson.

2007-06-20  Thomas Schwinge  <tschwinge@gnu.org>

        * lib/i386-io-hurd.h: Rewritten for new Hurd kernels.

2007-05-04  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.5.

        * pci.ids: Updated to the current snapshot of the database.

2007-02-14  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_express): Added PCI/PCI-X to PCI-Express Bridge type.
        Patch by Mark Glines.

2007-02-09  Martin Mares  <mj@ucw.cz>

        * pci.ids: Updated to the current snapshot of the database.

2007-02-06  Martin Mares  <mj@ucw.cz>

        * Replaced bzero() by memset() everywhere, it's better to lose a tiny
        bit of readability than maintain hacks to make it work on various systems.

        * lib/configure: tr on Solaris is a bit weird and it requires `[A-Z]'
        instead of `A-Z'. Fortunately, the extra brackets don't hurt otherwise.

        * lib/types.h, lib/configure: Solaris should use <stdint.h> to get precise
        integer types.

2007-02-04  Martin Mares  <mj@ucw.cz>

        * lspci.c: alloca() needs <alloca.h>.

2006-09-17  Martin Mares  <mj@ucw.cz>

        * lib/dump.c: Fixed a couple of bugs in the dump backend which caused
        devices with domains or with extended config space to be read incorrectly.
        Also, dumps with partial lines are allowed now.

2006-09-10  Martin Mares  <mj@ucw.cz>

        * pci.ids: Updated to the current database snapshot.

        * lspci.c (scan_device): If an error occurs when reading the standard config
        header of a device, report it and ignore the device and return with exit
        code 2 at the end.

2006-09-09  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.4.

        * maint/release: Remind the maintainer about the current PCI_LIB_VERSION.

        * lib/pci.h: Updated PCI_LIB_VERSION.

        * lspci.c (show_machine): In the `-m' mode, do proper shell escaping
        if the fields printed contain quotes or backslashes.

        * lspci.c (show_machine): Added a `-vmm' mode, which removes the misuse
        of the `Device' tag for two different purposes.

        * Makefile: Moved all system-dependent decisions to lib/configure,
        since config.mk is included in the top-level Makefile anyway.

        * lib/configure: When configuring for Linux, ignore the kernel version
        and always build all access methods.

        * Makefile (CFLAGS): Removed -Winline, it's not needed and triggers
        at many non-interesting places with gcc 3.4.

        * Whitespace cleanup of all source files.

        * The pci.ids file can be stored compressed if zlib is available.
        Added transparent decompression to lib/names.c, modified update-pciids.sh
        to keep the file compressed if applicable, updated Makefiles.
        Based on a patch by Matthew Wilcox, but all the bugs are mine.

        * Makefile, README: Allow installation to be done to a different directory
        from the one we will eventually be placed in by setting DESTDIR.
        Patch by Matthew Wilcox.

        * Added .gitignore files.

        * Makefile (clean): Clean *.orig, too.

        * Cleaned up usage of `char' and `byte'.

        * lib/header.h: PCI_CLASS_DOCKING_OTHER should be 0x0a80, not 0x0a01.

        * lib/header.h: Added PCI_CLASS_xxx constants for all classes currently
        defined in the pci.ids file.

2006-08-01  Martin Mares  <mj@ucw.cz>

        * lib/i386-io-hurd.h: Fixed a silly typo.

2006-07-30  Martin Mares  <mj@ucw.cz>

        * lib/Makefile: Added a missing rule for obsd-device.o.

        * lspci.c, lib/header.h: Added support for MSI per-vector masking.
        Contributed by Petr Vandrovec.

        * lspci.c, lib/header.h: Added support for the `bridge subsystem ID'
        capability. Contributed by Petr Vandrovec.

        * lspci.c (show_htype1): Fixed bug in printing of 64-bit prefetchable
        memory windows. Fix by Petr Vandrovec.

        * maint/release.pm: Exclude .git directory from releases.

        * lib/i386-ports.c, lib/i386-io-*: Report failures during port access
        initialization by a->warn() instead of calling printf() or perror()
        directly.

        * lib/i386-ports.c, lib/i386-io-*: Moved the logic which keeps track of
        the port access state to generic code.

        * lib/i386-io-hurd.h: Ask the kernel for I/O port access appropriately.
        Contributed by Thomas Schwinge and Samuel Thibault.

        * lib/i386-ports.c: Define _GNU_SOURCE, it's needed by the Hurd module.

        * lib/header.h: Whitespace cleanups.

        * lib/i386-io-windows.h: Fixed indentation and spelling.

        * README.Windows: Mention that WinIO.dll is needed and where to get it.

2006-06-27  Martin Mares  <mj@ucw.cz>

        * lib/Makefile, Makefile: Added rules for building and cleaning the example.

        * lib/example.c: Show how to use PCI_FILL_CLASS and used another register
        for demonstrating the config space accesses. The example is still very
        incomplete, though.

        * lib/pci.h, lib/generic.c: Added PCI_FILL_CLASS.

        * lib/sysfs.c: Fetch device ID and class from sysfs, because they can
        be modified by kernel fixups.

        * lspci.c: Use PCI_FILL_CLASS. Thanks to Matthew Willcox for the patch.

2006-06-03  Martin Mares  <mj@ucw.cz>

        * lspci.c: Introduced the -nn switch. Thanks to David N. Welton
        for the idea.

        * lib/names.c (pci_lookup_name): Introduced PCI_LOOKUP_MIXED and
        cleaned up the name selection code.

        * lib/names.c (pci_lookup_name): If PCI_LOOKUP_NO_NUMBERS is given,
        pci_access->numeric_ids is ignored.

        * lib/names.c (pci_lookup_name): When class is identified and
        subclass isn't, display class name and subclass number.

2006-05-31  Martin Mares  <mj@ucw.cz>

        * setpci.c (main): Don't crash when an invalid width is specified.

        * lspci.c, setpci.c, common.c: die() now uses the right program
        name when printing an error message.

2006-05-19  Martin Mares  <mj@ucw.cz>

        * README: Mention the public GIT tree.

        * README: Updated the list of ports.

2006-05-10  Martin Mares  <mj@ucw.cz>

        * lib/configure, lib/fbsd-device.c: Added support for GNU/kFreeBSD.
        Thanks to Petr Salinger for the patch.

2006-05-05  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.3.

        * lspci.c (scan_device): The -D switch didn't work as intended
        in -m mode.

2006-05-05  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.2.

        * pci.ids: Updated to the current database snapshot.

        * lib/obsd-device.c (and other files in lib/*): Added OpenBSD
        interface by Matthieu Herrb <matthieu.herrb@laas.fr>, based on
        the existing FreeBSD interface.

        * Moved pciutils to a GIT repository, which now contains merged
        history from both CVS and Arch. Good bye, TLA!

2006-03-21  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_slot_name): Avoid the previous changes in default
        display of domain name when in machine-readable mode. However, `-D'
        forces domain display even there.

        * lspci.man: Added a warning on -m being the only format, which is
        guaranteed to be stable between lspci versions.

2006-03-13  Martin Mares  <mj@ucw.cz>

        * lspci.man: Documented the -D switch.

        * lspci.c (show_slot_name, scan_device): If there are multiple PCI
        domains or if the `-D' switch is used, show the domain number for
        all devices.

        * lspci.c (show_verbose): Report cache line size in bytes.

        * update-pciids.sh: Use curl if available. Patch by Matthew Wilcox.

2006-01-04  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_express_link): Fixed decoding of link status register.
        Thanks to Roland Dreier for his report.

2005-12-12  Martin Mares  <mj@ucw.cz>

        * lib/nbsd-libpci.c: If libpci is used by an ordinary user, allow
        at least read-only access. Patch by Pavel Celeda <celeda@liberouter.org>.

        * Makefile: Corrected library path on NetBSD.

2005-11-26  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.1.

        * lspci.c (show_machine): Subsystem vendors were printed incorrectly
        in machine-readable modes. Thanks to Pavel Celeda for a bug report.

2005-10-11  Martin Mares  <mj@ucw.cz>

        * lspci.c (new_bus): Fixed a memory leak. Thanks to Paul Sangree for reporting it.

2005-09-21  Martin Mares  <mj@ucw.cz>

        * Released as 2.2.0.

        * pci.ids: Updated copyright header.

        * lib/sysfs.c (sysfs_get_resources): Removed warning about unsupported
        64-bit addresses, they are now always supported.

        * lspci.c (show_bases): Corrected printing of 64-bit addresses
        in bus-centric mode.

        * lib/configure: Enable 64-bit addresses on all Linux systems.

        * lib/types.h: Don't pad 64-bit addresses to 16 xigits, only to 8 if they
        are shorter.

2005-09-11  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test11.

        * lspci.c: Removed unnecessary trailing zeros in pci_lookup_name() calls.

2005-09-10  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test10.

        * pci.ids: Synchronized with the current database snapshot.

        * update-pciids.sh: Changed the default URL for downloading pci.ids
        to http://pciids.sourceforge.net/v2.2/pci.ids.

        * lib/pci.h (PCI_LIB_VERSION): Added version identifier.

        * lib/names.c: Rewritten the name database module almost from scratch.
        Everything is much cleaner and there are hopefully no more memory leaks;
        pci_lookup_name() now uses varargs in a backward compatible fashion.
        Introduced PCI_LOOKUP_NO_NUMBERS.

        The new code supports subsystem entries not tied to a specific device.
        I had to extend the format of pci.ids in order to support it, so I have
        extended the idea of the "C" (class) blocks and introduced "S" blocks
        for subsystems. To avoid doing more incompatible changes in the future,
        the parser skips unknown single-letter blocks without reporting errors.

2005-08-23  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test9.

        * Makefile (OPT): Removed -fomit-frame-pointer, it's default in recent
        gcc versions when optimizing anyway.

        * Made the path to pci.ids customizable and independent on the SHAREDIR.
        Just override IDSDIR in the top-level Makefile.

        * pci.ids: Synchronized with the current database snapshot.

        * lspci.man, setpci.man: Improved the man pages. Documented all access
        methods and which operations are privileged.

        * lspci.c: Another rewrite of config register caching, now also including
        lots of internal checks. It should be now perfectly able to cope with
        portions of the configuration space being inaccessible, for example
        due to insufficient access rights.

        * lspci.c (show_pcix_nobridge, show_pcix_bridge): Cleaned up dumping of PCI-X
        capabilities. Includes partial support for PCI-X 2.0 (probably incomplete
        as I haven't seen the spec).

        * lspci.c: Quell warnings about unused parameters.

        * lspci.c: Removed C++ comments.

        * lib/header.h: Merged definitions of extended capabilities and some new
        PCI-X capability bits from linux-2.6.11/include/pci.h.

        * lspci.c (show_caps): Try to scan extended capabilities only if the
        device has either PCI-X or PCI Express capability in its normal capability
        list.

        * lib/dump.c (dump_init): Reading of dumps works again. The dump reader
        now also remembers how much data it has read and refuses attempts to
        access more than that.

        * setpci.man, lspci.c, README: prefer spelling "buses" over "busses".

        * lspci.c: If alloca() is not available, use xmalloc(), not malloc().

        * lib/configure: Added x86_64 on Linux.

2005-08-22  Martin Mares  <mj@ucw.cz>

        * lib/filter.c (pci_filter_parse_slot): Fixed parsing of domain filters.
        Thanks to Matthew Wilcox for bug report.

        * lspci.c: Corrected spelling of "Hz" (it was "hz" at several places).
        Thanks to Krzysztof Oledzki for pointing that out.

2004-08-19  Martin Mares  <mj@ucw.cz>

        * pciutils.spec (%attr): Setting attributes for /sbin/* is an anachronism,
        because pciutils by default install to /usr/sbin. Update.

2004-08-13  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test8.

        * lib/types.h, lib/pci.h, lib/sysdep.h: `byte' and `word' are
        no longer exported to the outside world.

        * README.Windows: Updated.

        * maint/release: Substitute version number in win32/config.h.

        * win32/config.h: Added.

        * lib/sysdep.h (bzero, strcasecmp): are macros on Windows.

        * compat/getopt.[ch]: Added copies of getopt.[ch] from the GNU
        C library for use on systems where the default libraries lack
        proper getopt. Currently used by the Windows port.

        * lib/sysdep.h, lib/types.h: Updates of the Windows port from
        Alexander Stock.

        * lib/types.h: If PCI_HAVE_Uxx_TYPES is defined, libpci doesn't define
        its own u8, u16, u32, byte and word types and uses what the user
        has supplied instead. With this change, all namespace clashes should
        be gone.

        * Makefile, lib/Makefile: Updated dependencies.

        * pciutils.h: Include lib/sysdep.h and move NONRET et al. there.

        * lib/sysdep.h: No need to include <sys/types.h> on FreeBSD, because
        it is included unconditionally in lib/types.h.

        * Moved system-dependent stuff from lib/internal.h to lib/sysdep.h,
        which is also used by the utilities. Also moved type declarations
        from lib/pci.h to lib/types.h.

        * All files: Prepend a "PCI_" prefix in front of all configuration
        defines to avoid namespace clashes. CAVEAT: If there is any libpci
        application using the (undocumented) defines, it has to be updated.

        * lib/Makefile: Killed HAVE_OWN_HEADER_H, since we stopped sharing
        headers with the kernel a couple of years ago.

        * lib/sysfs.c (sysfs_get_resources): We have 7 resources, not 6.

        * lspci.c (show_rom): Use the same logic for printing disabled
        or unassigned ROM's as we do in show_bases() for the other BAR's.

        * lib/generic.c (pci_generic_fill_info): Better reaction to
        invalid 64-bit addresses. Also d->hdrtype should not include
        bit 7, which caused mysterious errors on multi-function devices.

        * lib/generic.c (pci_generic_fill_info): Fill in base addresses
        even if the regions are known to be disabled. It is the client's
        job to interpret them. (And it is not a trivial job if you want
        to do it correctly, since you need to check I/O and memory enables
        on all upstream bridges, too.) However, it could be interesting to
        introduce functions for interpreting the addresses and even for
        mapping the regions and doing I/O on them.

2004-07-30  Martin Mares  <mj@ucw.cz>

        * lspci.c: HyperTransport improvements from Maciej.

2004-07-11  Martin Mares  <mj@ucw.cz>

        * lib/sysfs.c (sysfs_get_resources): Arguments now correspond
        to the format string. [Patch by Bill Nottingham]

2004-07-05  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test7.

        * lspci.c (config_fetch): Wanted to merge Matthew's bug fix, but
        ended up with rewriting the fetching mechanism to be fully dynamic,
        but avoid reading config space registers not explicitly requested.

2004-06-29  Matthew Wilcox <willy@debian.org>

        * lspci.c: More work on PCI Express dumping.

        * lib/header.h: Updated PCI Express capability definitions.

        * lib/proc.c (proc_read): Removed bogus warning.

        * common.c (xrealloc): Introduced.

        * lspci.man: Added -xxxx.

2004-06-27  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test6.

        * lspci.c (show_msix), lib/header.h: Added dumping of MSI-X cap.
        Patch by Roland Dreier <roland@topspin.com>, cleaned up by me.

        * lspci.c (show_pcix_nobridge, show_pcix_bridge): Handle config_fetch()
        failures.

        * lib/header.h: Added PCI Express extended capabilities. Again by Matthew.

        * lspci.c (show_express): Added dumping of PCI Express cap.
        Patch by Matthew Wilcox.

        * lib/header.h: Added a list of PCI 3.0 capabilities and also details
        on PCI Express caps. Patch by Matthew Wilcox <willy@debian.org>.

        * lspci.c (check_root): Gone. No explicit checks for root are needed,
        report correct errors reported by the libpci instead.

        * lspci.c: Added dumping of the extended config space on "-xxxx".
        Better caching of config registers.

        * setpci.c (main): Allow access to whole 4096 bytes of the config space.

        * lib/sysfs.c, lib/proc.c: Don't print error messages on short reads,
        just return the appropriate error code.

        * lib: Added support for extended (4096-byte) configuration space,
        currently implemented only in Linux proc and sysfs access methods
        and of course in the dump reader.

2004-05-29  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test5.

        * lib/pci.h: Windows don't have the standard u_int* types.

        * lib/internal.h: <sys/param.h> required on Windows for endianity
        macros.

        * lib/i386-ports.c: Connected i386-io-windows.h.

        * lspci.c (check_root): geteuid() is not available on Windows.

        * lib/i386-io-windows.h: Added Windows port contributed by Alexander
        Stock <stock.alexander@gmx.de>.

        * lib/configure: Hopefully fixed SunOS port broken by various
        changes to the configure script.

        * Makefile, lib/configure: Cross-compilation support, patch by Maciej.

2004-05-28  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test4.

        * lspci.c (show_verbose): Header type 1 is probably legal for all
        types of bridges, not only for PCI-to-PCI bridges.

        * lspci.c (format_agp_rate): Write "x16", not "x@".
        (show_agp): rate[] could overflow.
        Bugs reported by Jakub Bogusz <qboosh@pld-linux.org>.

        * lspci.c (show_ht_*): Show HyperTransport capability with all its
        details. Once again code by Maciej simplified (i.e., possibly broken)
        by me.

        * lib/header.h: Added declarations of HyperTransport capability.
        Again thanks to Maciej.

        * lspci.c: Decode all bits of the secondary status word in type 1 headers.
        Thanks to Maciej W. Rozycki <macro@ds2.pg.gda.pl> for the patch.

2003-12-27  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test3.

        * lspci.man, setpci.man: Document domains and correct spelling.

        * lib/dump.c (dump_init): Added ability to read domain numbers.

        * lspci.c: Devices in domains different from 0 have their slot number
        printed as "<domain>:<bus>:<slot>.<func>". Tree view supports domains
        as well.

        * lib/filter.c: Slot filters understand domains.

        * lib/generic.c: Mention the domain in slot numbers in all error messages.

        * lib/internal.h: The #ifdef for Linux <asm/byteorder.h> was wrong.

        * lib/access.c (pci_get_dev): Added support for domains.

        * lib/sysfs.c (sysfs_scan): Read vendor and device ID from the config
        registers (or to be precise, leave it for the generic parts of the pcilib
        to do so) instead of reading them from the sysfs. It's faster this way.

        * lspci.c (show_pcix): Don't touch pci_dev->hdrtype, it's an internal
        variable. Better read it from the config registers (it's cached anyway).

        * lib/sysfs.c (sysfs_scan), lib/proc.c (proc_scan): Don't read the hdrtype.
          lib/generic.c (pci_generic_fill_info): If hdrtype is -1 (unset), read it.
          Saves lots of unnecessary file accesses.

        * lib/pci.h (PCIADDR_PORT_FMT): Use %llx instead of %Lx, because the latter
        is not supported by all C libraries.

        * Makefile: Always enter the lib directory (remember that we don't have
        full dependecies for the library in the top-level Makefile; hmmm, another
        thing to rewrite some day).

        * lib/sysfs.c: Added Linux sysfs access method based on the patch
        written by Matthew Wilcox <willy@fc.hp.com>.

        * lib/proc.c: Renamed the access method name from "/proc/bus/pci" to "Linux-proc".

        * lib/pread.h: The hacks to support pread on various versions
        of Linux libc moved there.

        * lib/proc.c (proc_setup): The return value of snprintf() varies
        between glibc versions, so we need to check both for a negative
        values and for too large values.

        * Removed last few references to the "Linux PCI Utilities", the
        package is pretty cross-platform now :)

2003-12-27  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test2.

        * README, pciutils.lsm, pciutils.spec: Use @VERSION@ to make the
        release scripts insert the current version. "make release" is gone.

        * maint/release, maint/release.pm: Added a new system of scripts for
        making releases including inter-version diffs etc.

        * Makefile: Cleaned up.

        * lib/fbsd-device.c: I patched another copy of this file by mistake,
        this time the version checks should be right.

2003-12-27  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.99-test1.

        * pciutils.h, common.c, lspci.man, setpci.man, lib/internal.h:
        Remove shadows of the syscall access method which was never
        implemented.

        * update-pciids.sh: Try to preserve permissions of the old file
        if chmod supports --reference. Should close Debian Bug #223740.

        * lib/proc.c (proc_setup): Increased path name length limit to 1024.
        Thanks for Redhat and Mandrake for inspiration.

        * lib/configure: Recognize ppc and ppc64, both have 64-bit addresses.
        Grabbed from Redhat (Fedora) patches.

2003-12-27  Martin Mares  <mj@ucw.cz>

        Merged bug fixes from Debian patches:

        * lspci.c (show_verbose): "Cache Line Size" should be capitalized.

        * lspci.c (show_pcix_nobridge): Added a missing newline.

        * lib/proc.c (proc_scan): When reading the header type, don't
        forget to clear the topmost bit indicating that the device has
        multiple functions.

2003-12-27  Martin Mares  <mj@ucw.cz>

        Updated the FreeBSD port. Thanks to Samy Al Bahra <samy@kerneled.com>
        for the patches:

        * lib/Makefile: Add ${FREEBSD_SYS} to the include path if it's defined.
        * lib/fbsd-device.c: Select the right set of system includes according
        to __FreeBSD_version.

2003-12-27  Martin Mares  <mj@ucw.cz>

        Merged support for Solaris on i386 by Bill Moore <billm@eng.sun.com>
        and cleaned up:

        * lib/configure: Recognize SunOS.
        * lib/internal.h: Learn how to recognize byte order on SunOS.
        * lib/i386-ports.c: Split OS-dependent I/O port access from i386-ports.c.
        * lib/i386-io-linux.h: Linux specific part.
        * lib/i386-io-hurd.h: GNU/Hurd specific part.
        * lib/i386-io-sunos.h: SunOS specific part.

2003-12-26  Martin Mares  <mj@ucw.cz>

        * lib/header.h (PCI_*_MASK): Cast to pciaddr_t explicitly.

        * lib/pci.h: Types declared in <sys/types.h> should be usable on all
        platforms we currently support, so kill the forest of #ifdef's and
        use them in all cases.

        * lib/pci.h: Use ULONG_MASK to decide whether we should use long
        or long long to represent a 64-bit address. Killed HAVE_LONG_ADDRESS.
        Define format strings for addresses, port numbers and IRQ numbers
        directly in pci.h.

        * lib/proc.c (proc_scan): Use PCIADDR_T_FMT for scanf'ing addresses.

2003-12-26  Marco Gerards  <metgerards@student.han.nl>

        Added support for the GNU Hurd (cleaned up by Martin Mares):

        * lib/configure [GNU]: Use the i386 ports for configuration access.
        * lib/i386-ports.c: Don't call iopl() on the Hurd.
        * lib/pci.h [OS_GNU]: Include <sys/types.h> and use it for defining
        u8 to u32.

2003-12-26  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_pcix_bridge, show_pcix_nobridge): Don't forget to call
        config_fetch() to ensure that the registers have been read. Thanks to
        Bill Wood <bill.wood@hp.com> for the patch.

        * lspci.c: Ensure that failure of config_fetch() is handled correctly
        at all places.

        * lspci.man: There was one more explicit reference to /usr/share/pci.ids.
        Changed to @SHAREDIR@. Patch from Maciej W. Rozycki <macro@ds2.pg.gda.pl>.

        * setpci.c (main): Better error messages.

        * setpci.c (ex_op): The demo mode should disable only writing, not reading.

        * setpci.man: The documentation was inconsistent on what should -D do.
        Document the new behaviour.

        * pciutils.h, common.c, setpci.c: Introduced a NONRET macro encapsulating
        the GCC specific __attribute__((noreturn)) and killed the hack with
        redefining __attribute__ on non-GCC compilers.

        * Makefile: Added missing dependencies. Parallel builds work now.
        Problem reported by Andreas Haumer <andreas@xss.co.at>, but I chose
        a different fix.

        * Makefile (MANDIR): Use `:=' instead of `=' to avoid executing the shell
        command every time $(MANDIR) is referenced.

        * lspci.c (main): The error message for `lspci -s' incorrectly mentioned
        a `-f' switch. Reported by Steve Finney <Steve.Finney@SpirentCom.COM>.

        * lib/generic.c: Removed memory leak in pci_generic_bus_scan().
        Reported by Gary Parnes <gary_parnes@terago.com>.

        * Replaced obsolete syntax of __attribute__((unused)) in the middle of
        parameter declarations (which is no longer supported by GCC 3.1) by the
        current syntax (attribute at the end). Thanks to pixel@mandrakesoft.com
        for reporting this problem.

        * Removed CVS $Id$ tags from all files.

        * Makefile: Added some more warnings.

        * setpci.c: Cleaned up mask/value code.

2003-12-08 Thayne Harbaugh <tharbaugh@lnxi.com>

        * setpci.c: Individual bits to be set can be specified as <value>:<mask>.

2003-11-29  Martin Mares  <mj@ucw.cz>

        * Imported the pciutils sources to my Arch repository. Good-bye, CVS.

2003-01-04  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.11.

        * Makefile: Changed configuration of installation directories --
        all paths are now set at the top of the Makefile instead of being
        scattered between the installation rules. The default installation
        now goes always to /usr/local regardless of the OS as most distributions
        already contain some version of pciutils and we don't want custom
        installations to interfere with the default ones.

        * Makefile: Removed a couple of ancient install hacks: we no longer
        try to avoid overwriting a newer pci.ids file (users are now expected
        to use update-ids) and we don't try to remove /etc/pci.ids (a long time
        has passed since the last version which used it).

        * Makefile: Paths to pci.ids in man pages automatically get the right path.

        * Added the update-ids utility.

        * lib: Removed partially implemented "syscall" access method which will
        probably never be needed.

2002-12-27  Martin Mares  <mj@ucw.cz>

        * lib/nbsd-libpci.c: Cleaned up and hopefully made it endian safe.

        * lib/generic.c (pci_generic_scan_bus): Added work-around for devices with
        discontiguous numbering of functions. This is already present in the Linux
        kernel for several years, but I forgot to update pciutils as well.

2002-12-26  Martin Mares  <mj@ucw.cz>

        * lib/header.h, lspci.c: Dump AGP3 flags and speeds.

        * lib/pci.h, Makefile: Removed HAVE_OWN_HEADER_H. Always use our own header,
        there is no reason to prefer the kernel version.

        * lib/proc.c (proc_scan): Don't forget to initialize hdrtype.

        * Added preliminary version of NetBSD support by Quentin Garnier
        <netbsd@quatriemek.com>.

2002-04-06  Martin Mares  <mj@ucw.cz>

        * lspci.c: Mention "-xxx" in the help.

2002-03-30  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.10.

        * Removed pci.ids from the CVS as they are now maintained separately.
        They are still included in the tarball, but if you are building pciutils
        from CVS sources or you want to get a newer ID file than the one distributed,
        just use "make update-ids" to download the most recent snapshot from
        pciids.sf.net.

        * Makefile, README: Updated accordingly.

        * Makefile: Added a couple of maintenance targets.

        * maint/*: Maintainer's utilities now reside here (present only in CVS,
        not in the tarball).

        * lib/names.c (parse_name_list): End-of-line comments are no longer
        supported. Hashes are now perfectly valid in all names and they start
        a comment only at the start of the line.

2002-03-26  Martin Mares  <mj@ucw.cz>

        * README: Rewritten.

        * Makefile: When the currently installed pci.ids file is newer than
        the version to be installed, don't overwrite it. Suggested by
        Jean Delvare <khali@linux-fr.org>.

2002-03-24  Martin Mares  <mj@ucw.cz>

        * lspci.c (show_pcix_bridge): Added PCI-X capability display.
        Contributed by Jeff Garzik <jgarzik@mandrakesoft.com>.

        * lib/header.h: Added PCI-X stuff. Again by Jeff.

        * Makefile (CFLAGS): -Werror is gone.

        * lspci.c (format_agp_rate): Fixed AGP rate reporting.

        * lib/filter.c (pci_filter_parse_slot): Allow bus 0xff, slot 0x1f and
        function 7.

        * lib/names.c (pci_lookup_name): When printing unknown subsystem vendor
        or device hexadecimally, don't confuse it with chip vendor/device ID.
        First reported by Marc Boucher <marc@mbsi.ca>.

2001-11-04  Martin Mares  <mj@ucw.cz>

        * Released as 2.1.9.

        * pci.ids: Synced with the PCI ID Repository at SourceForge
        (http://pciids.sourceforge.net/).

2000-08-25  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Updated ID's, synced with kernel 2.4.0-test7.

2000-06-13  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile (uninstall): Fixed.

        * pci.ids: ID updates.

2000-05-20  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 2.1.8.

        * pci.ids: ID updates.

        * lspci.c (show_verbose): Min/max latency is now printed in nanoseconds.

2000-05-04  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_verbose): If the header type doesn't match device
        class, just print a warning and still use the header type, assuming
        bogus class info.

2000-05-01  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_pm): Updated according to PCI PM specs 1.1.

        * pci.ids: Updated Contemporary Control ARCnet card entries.

        * pci.ids: Synchronized class list with latest PCI SIG documents.

2000-04-29  Martin Mares  <mj@albireo.ucw.cz>

        * lib/names.c (pci_lookup_name): Fixed the cheat.

        * lib/internal.h: Moved UNUSED/inline hacks above all other declarations.

        * pci.ids: Various ID updates.

2000-04-21  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 2.1.7.

        * pciutils.spec: Added German description.

        * lib/names.c (pci_lookup_name): Added a cheat for case that subsystem ID's
        are the same as device ID and just output subsystem name according to
        device name.

        * lib/proc.c: Use UNUSED instead of __attribute__((unused)).

        * lib/pci.h: Added the correct typedefs for AIX.

        * lib/generic.c (pci_generic_scan_bus): Export.

        * lib/configure: Detect AIX. Use "echo '...\c'" instead of
        "echo -n" if the shell isn't bash.

        * lspci.c: Avoid using alloca() if not compiled by GCC.
        (insert_dev): Avoid returning a void value.

        * Makefile: Choose which install utility to use according to
        OS type. Also use `-o' instead of `-or' in find arguments.
        Part of the AIX port.

        * lib/aix-device.c: Added AIX low-level interface. Contributed
        by Dave Johnson <ddj@brown.edu>, thanks a lot!

        * pci.ids: Few new ID's.

        * pciutils.h, lib/internal.h: Redefine __attribute__ and inline
        when not compiled by GCC.

2000-04-17  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 2.1.6.

        * pci.ids: Added a large batch of ID's contributed by Gunther
        Mayer <gunther.mayer@braunschweig.netsurf.de> and synced the
        list with the 2.3.99pre6 kernel.

Thu Mar  9 13:11:39 2000  Martin Mares  <mj@albireo.ucw.cz>

        * lib/example.c: Added a simple example of how to use
        the library.

        * lspci.man, setpci.man: Revealed --version. Well spotted
        by Adam Sulmicki.

        * pci.ids: Added lots of new ID's and synced with 2.3.50.

Tue Feb 15 00:16:21 2000  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 2.1.5.

        * pciutils.spec: Updated spec file from Andreas Jaeger. Now using
        %{_mandir} to find the right location to install manual pages to.

        * pci.ids: New ID's.

        * setpci.c (main): Don't crash when `-s' or `-d' is given with
        no argument.

Mon Jan 24 20:04:11 2000  Andreas Jaeger  <aj@suse.de>

        * lib/i386-ports.c: Include <asm/io.h> only on systems without
        glibc.

Mon Jan 24 11:24:43 2000  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile: Modified to work with the Linux FHS brain-damaged idea
        of putting man pages to /usr/share/man. Now we choose either /usr/man
        or /usr/share/man depending on which one exists.

Sun Jan 23 10:52:34 2000  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Synced with Linux 2.3.40.

        * Released as version 2.1.4.

Thu Jan 20 11:08:32 2000  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (scan_device): Fixed bug in reading of cardbus extensions.

        * lib/proc.c: pread/pwrite fixed again, this time on libc5 :(

        * lspci.c (format_agp_rate): Better formatting of AGP rates.

        * pci.ids: New ID's.

        * lib/configure: Added configuration for ia64 (the same as for Alpha).
        Patch from Stephane Eranian <eranian@cello.hpl.hp.com>.

Thu Jan 13 23:01:52 2000  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 2.1.3.

        * pci.ids: New ID's.

        * lspci.c: Alpha IO_FORMAT fix by Andrea Arcangeli.

        * lib/access.c: Corrected order of access methods -- it's wonderful how
        long could such a bug remain unspotted. Thanks go to Andreas Schockenhoff.

Sat Dec 11 23:34:48 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 2.1.2.

        * lib/names.c (pci_lookup_name): Fixed printing of unknown subsystem ID's.

Sat Dec  4 13:11:03 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 2.1.1.

        * pci.ids: Several new ID's.

        * setpci.c (exec_op): Don't forget to increment address after writing
        single value, so that `30.b=12,34,56,78' works as expected. Reported
        by Petr Soucek <petr@ryston.cz>.

Wed Nov  3 10:24:38 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_terse): If prog-if is zero, but it's present in the
        ID list, show it.

Sat Oct 30 11:06:35 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 2.1.

        * pci.ids: Synced to devlist.h in 2.3.24 kernel. Merged in
        lots of contributed entries.

Thu Oct 14 10:40:12 1999  Dave Jones    <dave@powertweak.com>

        * pci.ids: Added lots of subsystem definitions.

Sat Oct  9 14:32:28 1999  Martin Mares  <mj@albireo.ucw.cz>

        * setpci.man: Better example.

        * lspci.c: Resolve prog-if names.

        * lib/names.c: Adapted to new pci.ids syntax.

        * pci.ids: Reorganized the pci.ids file. Subsystems are listed
        under devices, classes can optionally contain prog-if information.
        New ID's, as usually.

Wed Sep 22 09:45:24 1999  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: New ID's. As usually.

        * lspci.c (show_htype1, show_htype2): Don't show `closed' bridge windows
        unless we're vvvery verbose.

Mon Sep 20 11:22:54 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_htype2): Don't forget a TAB before the "I/O window" line.

Tue Sep 14 09:31:01 1999  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: New ID's. Again.

Thu Aug  5 17:45:42 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_size): Don't show size if it's zero (usually
        due to bus-centric mode being enabled).

Tue Jul 20 13:25:09 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/pci.h: Types are OS dependent.

        * lib/internal.h: Byte order hacks are OS dependent.

        * lib/configure: Recognize FreeBSD. Also set OS_XXX according to the OS.

        * lib/Makefile, lib/access.c: Added fbsd-device target.

        * pci.ids: Added an entry for PLX 9080 bridges with subsystem ID
        incorrectly set to device ID.

        * README: Added a note that we support FreeBSD.

        * Makefile (PREFIX, ROOT): Set it depending on the OS.
        (%.8): Grrr, BSD date is not able to convert date formats the same way
        as GNU date does. Use sed instead.
        (install): Use `-c' when calling install.

        * lib/fbsd-device.c: Added FreeBSD /dev/pci access module contributed
        by Jari Kirma <kirma@cs.hut.fi>.

        * lib/proc.c: Rewrote the pread/pwrite things once again. Use pread
        and pwrite only when we are certain it's safe (i.e., glibc 2.1
        on all architectures or any libc on a i386 where we really know
        how to use syscalls directly). In all other cases, emulate it
        with lseek/read/write.

        * pci.ids: Some more IDs.

Mon Jul 19 14:10:36 1999  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Added IDs of parallel port controller cards as sent
        by Tim Waugh <tim@cyberelk.demon.co.uk>.

Wed Jul  7 00:55:48 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/proc.c (proc_scan): HAVE_LONG_ADDRESS instead of HAVE_64BIT_ADDRESS.

        * lspci.c: ADDR_FORMAT now depends on both HAVE_64BIT_ADDRESS and
        HAVE_LONG_ADDRESS.

        * lib/configure: HAVE_64BIT_ADDRESS now doesn't imply that the addresses
        are represented as long long. Introduced a new flag HAVE_LONG_ADDRESS
        to indicate this. Both Sparc architectures now use both 64BIT_ADDRESS
        and LONG_ADDRESS since they have 32-bit userland, but don't set LONG_ADDRESS
        on Alpha.

        * lspci.c (show_msi): Added dumping of the MSI capability.
        (show_slotid): The same for SlotID capability.
        (show_caps): Seperated capability dumping, because it should
        be used for both htype0 and htype1. Even PCI 2.2 doesn't mention
        layout of htype2, so I'm a bit unsure about it wrt capabilities
        -- they at least have to live somewhere else since address 0x34
        is already defined differently in htype2.

        * lib/header.h (PCI_STATUS_UDF): Marked as obsolete (PCI 2.2).
        (PCI_BASE_ADDRESS_MEM_TYPE_1M): Ditto.
        (PCI_CAP_ID_*): Added some new capabilities defined in PCI 2.2.

        * lspci.c (show_htype0): Mask out lowest 2 bits from all capability pointers
        (required by the PCI 2.2 specs).

Mon Jul  5 12:45:19 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_size): Added new function for dumping of region sizes.
        (show_rom): Added. Now correctly dumps unassigned ROM addresses, disabled
        ROMs et cetera.

        * lib/pci.h (struct pci_dev): known_fields moved to the public part
        of the structure.

        * Added support for region sizes. Needs support in the kernel, because
        sizes have to be scanned before drivers initialize yourself. pci_fill_info()
        now returns a bitmask of what fields were really read.

Mon Jun 28 18:37:51 1999  Dave Jones    <dave@powertweak.com>

        * Makefile:
          Added `uninstall' target - removes all traces of pciutils.
        * pci.ids:
          - Lots of cleanups in the ATI, S3, Adaptec vendors.
          - Changed Compaq QVision 1280/p definitions, as it's not possible
            to determine the revision from the device ID.
          - Same for the Tseng ET4000.
            The id's said I had a rev C, when it was actually a rev B.
          - Removed some unnecessary strings
            `PCI'. Unless it's an AGP card, it should be obvious that it's PCI.
            `Ethernet card'. This should be determined from config space.
          - Lots of other new vendors & devices
          - Other additional small cleanups.

Mon Jun 21 22:11:10 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/names.c (pci_lookup_name): When device ID lookup
        fails, return hexadecimal device ID instead of vendor ID.
        Well spotted by Axel Bodemann <Axel.Bodemann@ruhr-uni-bochum.de>,
        I've just extended the fix to subsystem ID's.

Thu Jun 17 19:48:21 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_agp): Bug fix from Petr Vandrovec
        <vandrove@vc.cvut.cz>. The command register was displayed
        incorrectly.

Wed Jun  2 22:42:44 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/proc.c (SYS_pread, SYS_pwrite): Use hard-coded
        numbers if not supplied by the libc.

Wed May 19 13:24:39 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released the whole package as version 2.0.

Fri May 14 22:42:02 1999  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Added several new ID's contributed by people
        on the linux-pci list.

Mon Apr 19 15:21:08 1999  Jakub Jelinek  <jj@ultra.linux.cz>

        * lspci.c: Display I/O addresses correctly on sparc64.
        * lib/header.h: Ditto.

        * lib/configure: On sparc set HAVE_64BIT* as well, we want
        a binary which works on both 32bit and 64bit SPARCs.

Sun Apr 18 21:14:58 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c, lib/proc.c: Alpha compilation fixes from Matthew Jacob
        <mjacob@feral.com>.

        * pci.ids: A lot of updates from Adam J. Richter <adam@yggdrasil.com>.

Sun Feb 28 22:26:21 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (do_map_bus): Don't dump functions 1--7 if not flagged
        as a multi-function device, because several single-function devices
        don't decode the function bits at all.

Sun Feb 14 23:48:22 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile (install): Don't use "-o root -g root" for installation
        since it breaks on machines where programs are not installed by root.
        Reported by Richard Gooch <rgooch@atnf.csiro.au>

Tue Feb  9 15:54:39 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_bases): Use new address masking macros and pciaddr_t.

        * lib/pci.h: Using pciaddr_t for bus addresses, which are 32-bit
        or 64-bit depending on CPU.

        * lib/pci.h (PCI_ADDR_MEM_MASK): Added macros for address masks
        according to bus address width.

Thu Jan 28 20:54:16 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 1.99.4.

        * lspci.c: Capability list parser now recognizes both AGP
        registers and PCI Power Management registers (the latter
        is mainly guesswork based on DEC/Intel 21153 bridge specs
        since I don't have the PCI Power Management document).

        * lspci.c: Replaced numerous occurences of (x & flag) ? '+' : '-'
        by FLAG macro.

        * lspci.c: Added bridge checks to bus mapping code.

Wed Jan 27 14:59:16 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c: Implemented bus mapping mode (-M).

        * lspci.c (scan_devices): Split to scan_devices() and scan_device().
        (show): Split to show() and show_device().

        * lib/access.c (pci_init): When a->method == PCI_ACCESS_AUTO,
        set it to the real access method afterwards.

Mon Jan 25 23:46:13 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/generic.c (pci_generic_fill_info): If in buscentric mode,
        don't check PCI_COMMAND for I/O and memory enables.

Mon Jan 25 21:28:49 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile: Added target `release' which substitutes new version
        number to .spec, .lsm and README. Also rewrote target `dist'.

        * Released as 1.99.3.

Sun Jan 24 22:10:36 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lib/header.h: Until kernel adopts new layout of PCI
        includes (i.e., separate declaration of header structure,
        functions and device IDs), which is not going to happen
        before 2.3, we'll use our own definiton of the header.

        * lspci.c (show_verbose): Display `Cap' flag in device status.

        * lspci.c (show_htype0): Display capability lists whereever
        available. The only capability name we recognize now is `AGP'.
        Unfortunately, capabilities are stored in device-dependent
        portion of the configuration space and are thus available
        only to root unless you read a dump.

        * lspci.c (scan_devices): Use cache instead of buffering.

        * lib/buffer.c: Removed (obsoleted by the cache).

        * lib/access.c: Added general caching mechanism.

Sat Jan 23 21:30:54 1999  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Added few devices.

Fri Jan 22 19:29:31 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Version string is now defined in top-level Makefile, exported
        to the configure script and also substituted to man pages.

        * lspci.c (show_bases): Rewrote displaying of 64-bit addresses.
        (show_verbose): Rewrote interrupt display logic.

        * lib/i386-ports.c: Include sys/io.h only on glibc systems.

        * lib/configure: Rewrote detection of Linux versions. Now it
        works on 2.0 kernels (only with direct/dump access, of course).

        * lib/internal.h: New bytesex macros using <asm/byteorder.h>
        whenever available.

        * lib/proc.c (proc_read, proc_write): Distinguish between short
        read/write and real errors.

        * lspci.c (show_htype{0,1}): Always use d->dev->rom_base_addr since
        libpci respects buscentric mode automatically.

        * lspci.c (show_hex_dump): For CardBus bridges, print out 128
        bytes of header (the whole standard part).

        * common.c: pcilib options are now all uppercase. Also moved
        PCI access debugging option here.

        * Released as 1.99.2.

Wed Jan 20 22:50:35 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Wrote configure script and rewrote Makefiles.

        * Removed few unused variables.

Wed Jan 20 12:21:56 1999  Martin Mares  <mj@albireo.ucw.cz>

        * common.c: Moved several functions used in both setpci and lspci
        here. This includes parsing of libpci-related options.

        * More library tweaks.

        * filter.c, names.c: Moved to library.

        * setpci: Rewritten to use the library.

        * Released as 1.99.1.

Tue Jan 19 23:00:12 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (scan_devices): For cardbus bridges, read first 128
        bytes of config space to get full standard header.

        * Makefile (CFLAGS): Removed "-Wno-unused".

        * Started the "New Generation" branch and introduced the
        PCI library.

        * lspci: Rewritten to use the library.

Tue Jan 19 22:24:08 1999  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 1.10.

Mon Jan 18 08:51:17 1999  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.8, setpci.8: Miscellaneous fixes as suggested by
        Dag Wieers <dag@digibel.be>.

Sun Nov 29 20:05:56 1998  Martin Mares  <mj@albireo.ucw.cz>

        * pciutils.spec (Name): Update from Krzysztof G. Baranowski.

Sun Nov 22 10:49:56 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile, pciutils.h: Moved pci.ids to /usr/share.

        * Released as version 1.09.

Wed Nov 18 15:47:05 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_htype1): Fixed displaying of prefetchable memory behind
        bridge. Thanks to Petr Vandrovec <vandrove@vc.cvut.cz> for bug report.

Fri Oct 23 18:59:19 1998  Martin Mares  <mj@albireo.ucw.cz>

        * setpci.c: Don't include <syscall-list.h> with glibc >= 2.1.

Mon Oct 19 21:53:30 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Released as version 1.08.

        * setpci.c: glibc 2.1.x already defines pread() and pwrite().

        * lspci.8: Changed warning about lspci -xxx.

        * lspci.c: Require "-xxx" for full configuration space dump, so that
        it's impossible to crash the machine by single typo.

        * specs: Added (courtesy of Krzysztof G. Baranowski <kgb@knm.org.pl>).

Wed Sep  9 12:03:24 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_bases): Better displaying of unassigned and
        disabled bases. Thanks to Gabriel Paubert <paubert@iram.es>
        for an idea.

Wed Sep  2 10:58:01 1998  Martin Mares  <mj@albireo.ucw.cz>

        * setpci.c (pread): Recognize glibc 1.99 numbered as 2.0 on the PPC.
        (thanks to Geert Uytterhoeven for finding this out)

Fri Jul 17 10:43:30 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_verbose): Print subsystem ID using the new resolver.
        (show_machine): Print subsystem ID.

        * names.c: New name resolution engine supporting subsystem IDs.

        * Released as version 1.07.

Wed Jul 15 15:37:21 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_htype2 etc.): Displaying of CardBus headers.
        (show_bases): Honor the `cnt' argument.
        (grow_tree): Parse CardBus headers in tree mode as well.

        * pci.h: Updated CardBus header field description. I still don't
        have the CardBus standard available, but OZ6832 specs contain
        full description of all header fields supported by the chip.

Tue Jun  9 22:53:59 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 1.06.

        * names.c (parse_name_list): Killed an unused variable.

        * setpci.c (pread, pwrite): Define SYS_(pread|pwrite) as __NR_\1
        if they are not defined by glibc (needed for glibc built on older
        kernels). Ugly.

        * setpci.c (exec_op): Fixed error messages. Thanks, Steve!

Mon Jun  8 10:59:22 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 1.05.

        * setpci.c: Problems with pread()/pwrite() with glibc on Alpha
        should be gone. Again thanks to Steve for bug report.

        * filter.c (filter_parse_slot): Fixed ":x" type filters.

        * pci.ids: Killed duplicate entry. Thanks to Stephen Williams
        <steve@icarus.com> for reporting this.

Sun Jun  7 19:27:51 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (main), setpci.c (main): Implemented "--version".

        * Released as 1.04.

        * pciutils.h (PCIUTILS_VERSION): Added version string.

        * filter.c, names.c: Extraneous #include <linux/pci.h> removed.
        Thanks to Geert Uytterhoeven <Geert.Uytterhoeven@cs.kuleuven.ac.be>
        for bug report.

Thu May 28 14:45:58 1998  Martin Mares  <mj@lomikel.karlin.mff.cuni.cz>

        * pci.ids: More updates from Jens Maurer.

Wed Apr 22 10:00:39 1998  Martin Mares  <mj@albireo.ucw.cz>

        * pci.ids: Updates from Jens Maurer.

Sun Apr 19 11:14:25 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Released as 1.03.

        * setpci.8: Written.

        * setpci.c: Finished.

        * lspci.c: Now able to fetch expansion ROM base from kernel device list
        and print it if not in buscentric mode.

Tue Mar 31 23:11:57 1998  Martin Mares  <mj@albireo.ucw.cz>

        * setpci.c: Added.

Sun Mar 22 15:39:08 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.8: Updated the documentation.

        * lspci.c: Modified to use the new filtering mechanism (options -f and -d).

        * filter.c: Introduced new generic device filter.

Thu Mar 19 17:03:48 1998  Martin Mares  <mj@lomikel.karlin.mff.cuni.cz>

        * lspci.c (grow_tree, show_tree_dev, print_it): Fixed displaying
        of PCI-to-PCI bridges in the tree format.

Sun Feb 15 10:12:25 1998  Martin Mares  <mj@albireo.ucw.cz>

        * lspci.c (show_machine): Added non-verbose mode of machine-readable
        dump.

        * pci.ids: Updates from Jens Maurer.

        * Released as version 1.02.

Thu Feb 12 16:53:28 1998  Martin Mares  <mj@lomikel.karlin.mff.cuni.cz>

        * lspci.c: Added a "-m" switch for dumping machine-readable
        configuration data (requested by Bjoern Kriews <bkr@cut.de>).

Mon Feb  9 13:17:43 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile, pciutils.h: Include local pci.h instead of <linux/pci.h>
        if available. This should avoid all problems with official kernel
        not synchronized to newer PCI code in CVS -- standard distribution
        of pciutils now contains pci.h from current CVS kernel, pciutils
        in CVS contain no pci.h and use the correct kernel include.

        * Makefile: Fixed installation path for man pages.

Sat Feb  7 15:15:46 1998  Martin Mares  <mj@albireo.ucw.cz>

        * README: Updated.

        * lspci.8: Created a man page.

        * Releasing as version 1.0.

Tue Feb  3 20:56:00 1998  Martin Mares  <mj@albireo.ucw.cz>

        * Makefile: Recognize architecture by calling uname and pass it as ARCH_xxx
        to all the C sources. This should eliminate problems with 32-bit compilers
        on sparc64.

        * lspci.c (show_verbose): Recognize CardBus bridge header type.
        (show_htype2): Stub routine.
        (scan_config): Write sensible error message if the kernel denies reading of
        upper part of the PCI config space.